Canon Pixma i320, i255
Step 1 : Manual for Service Mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
7. Connect USB cable
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
7. Connect USB cable
Step 2 : Software for permanent reset
1. Click the link below
2. Download the i255 General Tools, select (USB PORT)
3. Select EEPROM CLEAR and click SET DESTINATION 1
4. Insert the paper and the printer will print a printout of data EEPROM and perform tests for all nozzle printhead (black and color)
5. Turn off the printer.
2. Download the i255 General Tools, select (USB PORT)
3. Select EEPROM CLEAR and click SET DESTINATION 1
4. Insert the paper and the printer will print a printout of data EEPROM and perform tests for all nozzle printhead (black and color)
5. Turn off the printer.
Canon MP160 , MP145
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)
Error Code :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error
Canon pixma ip1700, 1880, 1600, 1200, 1300
Manual for Service Mode
Turn off the printer
1. Disconnect the power and USB cables
2. Press and hold the POWER button, plug the cable POWER
3. Press the RESUME 2x, release the POWER and RESUME
4. Lights will be blinking for a moment, wait until the light is on steady
1. Disconnect the power and USB cables
2. Press and hold the POWER button, plug the cable POWER
3. Press the RESUME 2x, release the POWER and RESUME
4. Lights will be blinking for a moment, wait until the light is on steady
Software for permanent reset
1. Plug the USB cable
2. Please open GENERAL SOFTWARE TOOLS and select USB PORT
3. Check in EEPROM CLEAR
4. Click once MAIN (printer lights will blink 1x)
5. Then click the TEST PATTERN 1
6. Turn the printer off
2. Please open GENERAL SOFTWARE TOOLS and select USB PORT
3. Check in EEPROM CLEAR
4. Click once MAIN (printer lights will blink 1x)
5. Then click the TEST PATTERN 1
6. Turn the printer off
Canon ip1880, MP145, MP530
This occurs because the ink level in catrik read out by the printer, although still a lot of ink in infusion or just the refill.
To overcome this guampangggg enough .... aja press the Resume button for several seconds (5-8 seconds) after the ink level will become automatic reset and the printer will continue printing.
The same goes for the printer Canon ip1200, 1300,1600,1700,2200.
As for the type of Canon MP160, MP145 simply press the COLOR button to reset the ink level ...
For higher multfunction type, such as type MP530, MP500, MP830, MP800 (like) can by pressing the STOP button.
To overcome this guampangggg enough .... aja press the Resume button for several seconds (5-8 seconds) after the ink level will become automatic reset and the printer will continue printing.
The same goes for the printer Canon ip1200, 1300,1600,1700,2200.
As for the type of Canon MP160, MP145 simply press the COLOR button to reset the ink level ...
For higher multfunction type, such as type MP530, MP500, MP830, MP800 (like) can by pressing the STOP button.
Solutions E16 Error on Canon MP series
If you search what's that mean E16 at printer Canon MP Series, the error E16 code is Failed to scan head alignment sheet. I will tell you how to fix the E16, see at below :
- If you see at Printer Status monitor while you printing, you will get the dialog it says your ink is running low.
- So what you need to do? Press the START button, then until 2-3 second press START button again.
I hope that will resolve your problem about error E16.
Code E16 on the printer Canon MP series, meaning "Failed to scan head alignment sheet. "
I will try to tell you how to fix this E16.
- If you see at Printer Status monitor while you printing, you will get the dialog it says your ink is running low.
- So what you need to do? Press the START button, then until 2-3 second press START button again.
I hope that will resolve your problem about error E16.
Code E16 on the printer Canon MP series, meaning "Failed to scan head alignment sheet. "
I will try to tell you how to fix this E16.
* Note the Status Monitor on your printer, it would appear the statement that will run out of ink (ink is running low)
* All you have to do is press the START button, then wait 2-3 seconds and then press the START button again.
* All you have to do is press the START button, then wait 2-3 seconds and then press the START button again.
Canon PIXMA ip1000
Step 1: Manual for Service mode
Step 1: Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
7. Connect USB cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
7. Connect USB cable.
Step 2 : Software for permanent reset
1. Reconnect the printer cable.
2.Open General Tools T5061 and select (USB PORT)
3 .Check on EEPROM CLEAR
4. Click TEST PATTERN 1
1. Reconnect the printer cable.
2.Open General Tools T5061 and select (USB PORT)
3 .Check on EEPROM CLEAR
4. Click TEST PATTERN 1
1. Go to the SERVICE MODE.
by pressing Menu, Copy, Scan, Copy, Copy (just press the button sequence, jgndetained )
2. Select TEST MODE.
3. Select (8) PRINTER TEST in TEST MODE.
4. Select 3. (EEPROM CLEAR).
5. Piliht 0. (INK COUNT).
6. Press the (Set)
7. Press the (Stop / Reset), then press the (ON / OFF)
1 Commen:
Sir, It went exactly the same as you mentioned for IP1300 but after turning off the printer at last 6th step, the printer lights again become unstable. Please help me out sir!
Posting Komentar